ASTM A564 PDF


Best Stainless offers high quality standards including UNS S, AMS , ASTM A, and ASTM A Grade PH stainless steel can be used. This standard is issued under the fixed designation A /A M; the number . [ mm] round bar, 10 to 12 ft [ to m] in length, ASTM A See the chemical composition and physical properties of ASTM A Grade condition HM, find alternative materials, and connect with suppliers.

Author: Zuzuru Grom
Country: Somalia
Language: English (Spanish)
Genre: Career
Published (Last): 6 October 2017
Pages: 380
PDF File Size: 4.78 Mb
ePub File Size: 12.67 Mb
ISBN: 329-5-27993-246-5
Downloads: 58565
Price: Free* [*Free Regsitration Required]
Uploader: JoJozil

E L – Longitudinal axis of specimen parallel to direction of grain ow during rolling or forging. Type UNS S is suitable for machining in the solution-annealed, cold-worked, and aged-hardened condition.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Note 2 — For billets and bars for forging see Specification A TypesXM, aatm XM may be furnished in the solution-annealed or age-hardened condition. For billets and bars for forging see Specification A Billets or bars for reforging may be purchased to this specication. The material shall be subjected to tension, impact, and hardness tests.

G Either Rockwell C hardness or Brinell is permissible.

ASTM A – Martensitic Stainless Steel

F Columbium plus tantalum 0. Combining values from the two systems may result in nonconformance with the specification. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Historical Version s – view previous versions of standard. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at aastmfaxor service astm.

  ANTROPOMETRIA DE LA VIVIENDA XAVIER FONSECA PDF

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Type and stainless steels contain a large amount of ferrite in the microstructure and can have low ductility in forgings and large diameter bars.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It aetm informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Time refers to minimum time material is at temperature and may be extended to obtain required ductility properties. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM A 564

C Unless otherwise noted, temperatures shown are suggested temperatures and may be varied to obtain required tensile properties. The limiting permanent offset shall be 0. I Refer to Table 2 for details on equalize and over temper heat treatment.

Up to 4 in. The tests shall meet the requirements of Table 4. A superscript epsilon indicates an editorial change since the last revision or reapproval. They are suitable for machining in the solution-annealed condition after which they may be age-hardened to the mechanical properties specified in Section 7 without danger of cracking or distortion.

  GORAZDE JOE SACCO PDF

Current edition approved May 1, Applications should be limited to small diameter bar. Materials and Manufacture 5. Link to Active This link will always route to the current Active version of the standard. D BH for rounds cold drawn after solution treating. Combining values from the two systems may result in nonconformance with the specification.

A 87 [] 58 [] Work Item s – proposed revisions of this standard. This standard has been approved for use by agencies of the Department of Defense.

Hold for not less than 3 h. Hot-nished or cold-nished rounds, squares, hexagons, bar shapes, qstm, tees, and channels are included; these shapes may be produced by hot rolling, extruding, or forging. Active view current version of standard.

When specied, the material, as represented by impact test specimens, shall be capable of developing the impact property requirements specied in Table 4 when heat treated in accordance with 5. Such requirements may include but are not limited to the following: The zstm shall be heat treated in accordance with 5. Unless otherwise specied in the purchase order, the condition of hardening heat treatment shall be at the option of the producer. Work Item s – proposed revisions of this standard.

The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Type XM is machinable in the as-received fully heat treated condition.