ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.

Author: Grole Mautilar
Country: Liberia
Language: English (Spanish)
Genre: Video
Published (Last): 9 April 2013
Pages: 352
PDF File Size: 18.31 Mb
ePub File Size: 5.25 Mb
ISBN: 634-3-52791-806-8
Downloads: 88500
Price: Free* [*Free Regsitration Required]
Uploader: Fezilkree

Lower hydrogen may be obtained by negotiation with the manufacturer. Approved May 1, The chemical analysis shall be conducted by the standard techniques normally utilized by the manufacturer and purchaser. In titanium these elements include aluminum, vanadium, tin, iron, chromium, molybdenum, niobium, zirconium, hafnium, astk, ruthenium, ashm, yttrium, copper, silicon, cobalt, tantalum, nickel, boron, manganese and tungsten.

Silicon each total 0. NOTE 2—If the longer dimension is under 36 in. Heat numbers shall occur at least 3 times across the width of the sheet and at intervals not greater than 2 ft 0. E For Grades 5, 6 and 32 the elongation on materials under 0. The markings shall have no deleterious effect on the material or its performance. Annealed atm may be furnished as descaled, as sandblasted, or as ground, or both sandblasted and ground.

Two bends shall be made asmt the L direction and two in the T direction. Samples for analysis should be stored in suitable containers. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.


Alternate Yield Strength Maximum S2. Other elements may not be added intentionally. For plates of irregular shape, the over thickness tolerances apply to the greatest width corresponding to the width ranges shown. A superscript epsilon indicates an editorial change since the last revision or reapproval. The characters shall be not less than 38 in. Ingot hydrogen need not be reported.

Grades 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Mechanical properties for conditions other than annealed or plate thickness over atm in. B Bend to Radius of Mandrel, T equals the thickness of the bend test specimen. Permissible Variations in Dimensions 7.

The test report shall, at minimum, indicate acceptable or unacceptable results. There is no under tolerance in weight for titanium sheets, under tolerance being restricted by the permissible thickness variations. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Committee B10 has identied the location of selected changes to this standard since the last issue B – 09 that may impact the use of this standard.

Each pair of these bends will place opposite surfaces of the sheet or plate material in tension. A number in parentheses indicates asrm year of last reapproval. Special Flatness Requirements S3. Product analysis limits shall be as specied in Table 3. G Properties for material in the solution treated condition.

Titanium Plates, Sheets & Coils, Titanium ASTM B Gr2 Plates, Titanium Gr5 Sheets

In titanium these elements typically include aluminum, b2655, tin, chromium, molybdenum, niobium, zirconium, hafnium, bismuth, ruthenium, palladium, yttrium, copper, silicon, cobalt, tantalum, nickel, boron, manganese, and tungsten. This abstract is a brief summary of the referenced standard. NOTE 4—The maximum deviation from a at surface does not bb265 exceed the tabular tolerance for the longer dimension specied.


Current edition approved May 1, Referee Test and Analysis Bend tests are not applicable to material over 0. Other elements may be present in titanium or titanium alloys in small quantities and are inherent to the manufacturing process. The grades of titanium and titanium alloy metal covered by this specification shall bb265 the chemical composition requirements of: Other industry standard methods may be used where the ASTM test methods in 2.

Titanium Plates, Sheets & Coils

Originally approved in The width of the bend test specimen shall be at least 5 qstm the thickness. Tensile properties shall be determined using a strain rate of 0.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Aluminum Vanadium Palladium Ruthenium 0. If the results of the retest conform to the specication, then the retest values will become the test values for certication. Link to Active This link will always route to the current Active version of the standard.