E3C-VS1G OMRON PDF


Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Darg Tegami
Country: Central African Republic
Language: English (Spanish)
Genre: Education
Published (Last): 19 August 2009
Pages: 80
PDF File Size: 19.69 Mb
ePub File Size: 8.48 Mb
ISBN: 309-5-58988-741-8
Downloads: 43548
Price: Free* [*Free Regsitration Required]
Uploader: Mik

For this type of application, separate the Sensors by at least 1. Typical measures are as given in the following table. When in doubt, special model numbers may be assigned to?

The axis from the center of the lens to the center of the beam for the Emitter and the axis from the center of the lens to the center of the reception area for the Receiver. Keep organic solvents away from the Sensor. Be sure to connect or disconnect the connector after turning OFF the E3c–vs1g.

Lock and unlock the fibers at an ambient temperature of? If not grounded, switching noise in the power supply may cause malfunction. Use the following methods to attach and remove Fiber Units.

Otherwise, it may malfunction or fail. Insert a capacitor e. Countermeasure Concept Use a Sensor with the interference prevention function. Placing them in the same conduit or duct may cause damage or malfunction due to induction interference. Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Type of noise Noise intrusion path and countermeasure Before countermeasure Noise enters from the noise source through the frame metal.

  ENTREVISTA PSIQUIATRICA EN LA PRACTICA CLINICA MACKINNON PDF

Dirt should be gently wiped off with a dry cloth. Hold the connector cover to connect or disconnect the connector. Power Supply Types An unsmoothed full-wave or half-wave rectifying power supply cannot be used.

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output

Light may enter even if the Sensors are separated by more than the sensing distance. Strong, conductive electrical wire 2 x 0.

Although the bending repetition tolerance of a standard cable is approximately 13, times, robot cable has an excellent bending tolerance of approximatelytimes. Secure the connector cover by hand. AC Two-wire Sensors Example: Power line Work Required for W3c-vs1g Leads Unused leads for self-diagnosis outputs or other special functions should be cut and wrapped with insulating tape to prevent contact with other terminals. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

To maintain the fiber characteristics, make sure that the lock is released before removing the fibers.

OMRON Products – Scattergood & Johnson

Use a soft, dry cloth to clean the Sensor. If Sensors are mounted in opposite each other, slant the Sensors as shown in the following diagram. Doing so may cause explosion or burning. This information by itself is not suf? Mutual Interference Prevention Polarizing Filter: Lowering the sensitivity will generally help.

The following are some examples of applications for which particular attention must be given. Do not use thinner or other organic solvents. Optical energy does not act as an ignition source, thus there is no danger of explosion or fire.

  CRA RC59 PDF

The following measures can be taken to avoid mutual interference. If the connector is not connected securely, the connector may be disconnected by vibration or the proper degree of protection of the Sensor may not be maintained. Exceptions are indicated in Safety Precautions in individual product information. Lens and Case The lens and case of the Photoelectric Sensor are primarily made of plastic. Be sure to insert a load when connecting the power supply. Typical examples include the minimum sensing object, engineering data, step height detection data, and selection list for specifications.

Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch

Separate the noise source and the Sensor to lmron distance where noise does not affect operation. Cable Tensile Strength When wiring the cable, do not subject the cable to a tension greater than that indicated in the following table.

Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, use Sensors with the interference prevention function. For bending-resistant cable, see Attachment to Moving Parts on page C For the E3S-C, the optical axis and the mechanical axis are the same, so the optical axis can be easily adjusted by aligning the mechanical axis.

Do not subject a shielded cable or coaxial cable to tension. Insert a capacitor, etc.