international certification bodies for its quality system and environmental management system. E5jK-T Series. E5CK-T. E5AK-T/E5EK-T. 1/4 DIN. 1/8 DIN. Omron E5AK Controllers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Omron E5AK Controllers. E5AK-TAA AC Omron Automation and Safety Controllers PROCESS CONTROLLER datasheet, inventory, & pricing.

Author: Muzshura Mezikazahn
Country: Indonesia
Language: English (Spanish)
Genre: Automotive
Published (Last): 7 December 2016
Pages: 228
PDF File Size: 5.62 Mb
ePub File Size: 5.13 Mb
ISBN: 321-5-81586-862-2
Downloads: 76125
Price: Free* [*Free Regsitration Required]
Uploader: Grorn

If the heater power supply is turned conditions ON after turning the E5AK power supply On, the heater burnout alarm is output.

OMRON E5AK User Manual

The process Calibration item SP The output ranges of the SP setting, set point or process value when temperature input is selected are the ranges sup- ported by the selected sensor. Page The display changes to [ ] 5 V calibration display. F Action Must repair. Page 31 Permissible load impedance: SP setting lower limit to SP setting upper limit 0: SP ramp function is enabled. The following figure shows the required device connection.

F Do not cover the area around the E5AK. If you select the desired mode using the About The Communications Function 1. For details on the communications function, refer to Chapter 6. Connect the input as fol- lows: However, when actually creating programs, do not leave spaces between frame items.

Assign these output functions to control output 1, control output 2, auxiliary output1, and auxiliary output2.

Though a shorter pulse period provides better control performance, the control period should be set taking the life expectancy of the output unit into consideration when the output unit is relay.


In a hold status, both control outputs 1 and 2 are OFF. The upper limit is set for the heating side positive valueand the lower limit is set for the cooling side negative value as shown in the follow- omfon figure. Use this chapter as a reference guide.

The following conventions eak used to indicate and classify precautions in this manual.

Al- ways heed the information provided with them. In other words, you cannot switch between e5a auto and manual operations by key operation. Page J Output Unit Ratings and Characteristics Ratings and characteristics conform to the output unit mounted on the controller. When the value on the No. Page setup mode can be used. Page AT hysteresis 0.


Dead time will be measured from the time the Temperature Controller starts operating. This character must be inserted before the lead- ing byte. E5a 13 Assign these output functions to control output 1, control output 2, auxiliary output1, and auxiliary output2.

The E5AK controller is calibrated before shipment from the factory. Also, omfon the input type, temperature unit and scaling sensor range are changed, set point limiter is forcibly reset to the scaling sensor range.

Omron E5AK-AA Processor/Controller | eBay

By pressing ‘print’ button you will print only current page. These abbreviations mean the following.

The parameter default is [ 4 As the oomron in this example is to be left as it is, press the key. Each press of this key switches between the auto and manual opera- tions. The display changes to the menu dis- play. Be sure to turn on the power supply to the load either before or simultaneously with the start of Temperature Controller opera- tion.


This description assumes that the controller is operated under the fol- lowing conditions.

Page Set point Stable range Set to Set the control period taking the control characteris- tics and life expectancy of the controller into consideration. When another mode is selected while in these modes, reset is canceled. Page 4 The following conventions are used to indicate and classify precautions in this manual. However, if the E5AK controller must be calibrated by the user, use the parameters provided for user to calibrate temperature input, analog input voltage, current and transfer output.

Got it, continue to print. Don’t show me this message again. Omton Dead band The dead band is set with the set point as its center. In a close status, only control output 2 is ON. Set- ting a positive value produces a dead band, while setting a negative value produces an overlap band. Machine automation controller nx-series ethercat coupler unit pages.

First-time users should read this chapter without fail. Of these, only the alarm assigned as the omro can be used. Ensure sufficient space e5aj the control- ler to allow heat radiation.

To give Function priority to stability, increase the set value of this parameter. So, d5ak control is made possible. You can select this mode only when the option unit is set in the controller.