FTR USB UART IC Datasheet Version Clearance No.: FTDI# •. •. Neither the whole nor any part of the information contained in, or the product. FTDI FTRL: available from 8 distributors. Explore Integrated Circuits ( ICs) on Octopart: the fastest source for datasheets, pricing, specs and. FTRL Datasheet, FT FTDI USB to Serial UART IC Datasheet, buy FTRL USB to Serial UART IC.
|Published (Last):||2 May 2009|
|PDF File Size:||7.81 Mb|
|ePub File Size:||12.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
This example uses the Sipex SP device. Rx relative to the USB interface. Low operating and USB suspend current. The centre pad on the base of the FTRQ is not internally connected, and can be left unconnected, or connected to ground recommended. The soft start circuit example shown in Figure 6. The FTR supports all standard baud rates and non -standard baud rates from Baud up to 3 Mbaud.
T his product or any variant of it is not intended for us e in any medic al appli anc e, devic e or s ys tem in whic h the failure of the produc t might reas onably be expec ted to res ult in pers onal injury. A frequently asked questions datawheet has been created here.
UART signal inversion option. The device is a USB 2. FTRQ-Reel is 6,pcs taped and reel packing 1. Y our s tatutory rights are not affec ted. The FTR adds two new functions compared with its predecessors, effectively making it a “3-in-1” chip for some application areas. Adjustable receive buffer timeout.
New CBUS bit bang mode option. T his produc t and its doc umentation are s upplied on an as – is bas is and no warranty as to their s uitability datzsheet any partic ular purpose is either made or implied.
FTR Datasheet(PDF) – Future Technology Devices International Ltd.
Datasheett are many suitable level converter devices available. Name Type Description be used. When a non -standard baud rate is required simply pass the required baud rate value to the driver as normal, and the FTDI driver will calculate the required divisor, and set the baud rate. This number cannot be reprogrammed. N o freedom to us e patents or other intellectu al property rights is implied by the public ation of this doc ument.
N either the whole nor any part of the information c ontained in, or the produc t des c ribed in this manual, may be adapted or re produc ed in any material or elec tronic form without the prior written c ons ent of the c opyright holder. This option will be described more fully in a separate application note available from FTDI website www.
In-built support for event characters and line break condition. Handshaking is handled in hardware to ensure fast response times. It has been designed to operate efficiently with a USB host controller by using as little as possible of the total USB bandwidth available. Web based applications can be used to maintain product licensing this way.
Preheat datashfet Temperature Min T s Min. The FTR will fail to operate when the internal oscillator has been disabled, but no external oscillator has been connected.
A digital one -shot is used so that even a small percentage of datasneet transfer is visible to the end user. For details on how to use an external crystal, ceramic resonator, or oscillator with the FTR, please refer to Section 7. In addition, asynchronous and synchronous bit bang interface modes are available. FIFO receive and transmit buffers for high data throughput. With the FTR it is possible to do this entirely in hardware by modifying the example shown in Figure 7.
FT232RL USB to TTL Serial Module
Corrected Tape and Reel quantities. Enter the email address you signed up with and we’ll email you a reset link. In accordance with the USB 2. No Supports bus powered, self-powered and high- USB specific firmware programming required.
FTR USB UART IC Datasheet | Kevin Zaat –
These configurable options are 1. Packing codes for xxxx is: Equivalent devices are available from Maxim and Analogue Devices. Various 3rd party drivers are also available for other operating systems – see FTDI website www.
It requires an external decoupling capacitor to be attached to the 3V3OUT regulator output pin. Skip to main content. Datasheey can be done using a link to switch the VCC supply. N eith er the whole nor any part of the information c ontained in, or the produc t d es cribed in this document, may be adapted or reproduc ed in any material or elec tronic form without the prior written c ons ent of the c opyright holder.
FT232RL USB to UART Breakout Board
Device supplied preprogrammed with unique USB serial number. Values are shown for both a completely Pb free solder process i.
A suitable device to do this is an International Rectifier www. Receive data LED drive: It performs asynchronous 7 or 8 bit parallel to serial and serial to parallel conversion of the data on the RS or RS or RS interface. Refer to Section 3. If not required can be left unconnected, or pulled up to VCC. This gives achievable baud rates in the range It is recommended to ground the central heat sink area of the device.
Auto transmit buffer control for RS applications. The device is supplied with the most commonly used pin definitions pre -programmed – see Section 8 for details.